Getting Started with Plumber's Essentials for Bathtub Installation
Getting Started with Plumber's Essentials for Bathtub Installation
Blog Article
The content listed below on the subject of A Step-by-Step Guide to Installing a Bathtub is highly enlightening. Try it and draw your own personal conclusions.
Mounting a bathtub isn't precisely rocket science, but it does call for solid plumbing, woodworking, as well as occasionally, tiling skills. Changing an old bathtub with a brand-new one is also a moderately hard project. If the old bathtub is conveniently easily accessible, the task can move immediately; if you need to open a wall to eliminate the old bathtub and position the new tub, the job is a lot harder. In either case, the project is within a house handyman's skills, although you will certainly require an assistant to vacate the old tub as well as embeded in the brand-new one. See to it you have actually certified on your own for the work and also fit trying it. Instead of employing a service provider to take control of a halfway-completed job, it is much better to think about employing one before you start. Opportunities are you may need a professional plumber to make tube links.
This post will help you mount a new bathtub in your washroom if you have actually already acquired a brand-new tub and also don't require to alter the arrangement of your previous water pipes.
Your devices and product checklist need to make up the following:
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your setup, after that the first thing you must do is detach the water supply. After doing so, turn on the taps to drain any type of water staying in the system. The process of eliminating the existing taps can be quite problematic due to the restricted access that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a cloth ready for the remaining water that will certainly originate from the pipes. Once the supply pipes have actually been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from turning throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old securing compound.
Before going on to fit the new taps, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to stop damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a link to the existing supply pipes.
If you need to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the installing opening in the bath/basin ensuring that the washing machines remain in area in between the faucet and also the sink. Protect the tap in place with the producer offered backnut. Once the faucet is firmly in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet ports. The former kind ought to be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Installing the Bath tub
Using both wooden boards under its feet, put the bath tub in the required setting. The wood boards are valuable in equally spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little factors.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the level and also changing the feet on the tub till the spirit level checks out degree.
To mount faucets, fit the bottom of the furthest versatile faucet connector to the suitable supply pipe by making a compression join; after that do the very same for the various other faucet.
Activate the supply of water as well as inspect all joints as well as brand-new pipework for leakages as well as tighten them if needed. Fill up the tub and likewise inspect the overflow outlet and the normal electrical outlet for leakages.
Lastly, take care of the bathroom paneling as defined in the maker's instruction manual. Tiling and securing around the bath tub must wait until the bath tub has actually been utilized at least when as this will resolve it right into its final placement.
Getting ready for the Installation
To start with, the supporting structure supplied with the bathroom must be fitted (if required) according to the maker's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to ensure that if the faucet features a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the taps device to prevent pressure on the bathtub.
Fit the flexible faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use every one of the provided washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now be ready to be suited its last setting.
Tiling Around the Bathtub
In the location where the bathroom satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to break a stiff seal, causing the water to penetrate the wall surface in between the bath and the tiling, resulting in problems with wetness as well as possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your fixtures as well as installations. They are offered in tubes and cartridges, as well as can sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched paper or soft rope. Remember to always load the bathtub with water before sealing, to permit the movement experienced when the tub remains in usage. The sealer can crack relatively early if you do not think about this activity prior to securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise easily available on the market. It is advisable to fit the tiles making use of water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a fervent person who reads on How to Install a Bathtub, I assumed sharing that segment was worthwhile. Are you aware of another person who is curious about Tools You Need to Install a New Bathtub ? Take a moment to promote it. We value reading our article about A Step-by-Step Guide to Installing a Bathtub.
Quality assured, call! Report this page